Brava Shake Tile Roofing in Greater Seattle

Home / Brava Tile Roofing / Shake Brava

Master Craftsman crew | Licensed & insured | Greater Seattle

Brava Shake Tile Roofing in Greater Seattle

Cedar curb appeal without wood soak and moss rot—Construction Elite LLC installs and repairs Brava shake composite across King, Snohomish, and Pierce Counties. Shake needs keyway spacing (about 3/16 in. min; ~3/8 in. preferred), a full tear-off (no overlay over shingles), and corrosion-resistant ring-shank fasteners into the deck. For curved Mediterranean barrel tile, see Spanish Brava S-Tile.

Up to 30-year manufacturer warranty on qualifying materials
5-year workmanship warranty on qualifying labor

Get free estimate

Our services

Emergency roof repair

Certified crew
Manufacturer-trained installation to spec.
Licensed & insured
Fully licensed and insured. Verify on L&I
5-star rated
Trusted by homeowners across Greater Seattle.

When to schedule Brava shake tile roofing

Closed-cell composite shake resists the water soak that drives cedar moss and rot in the PNW—but the system still fails when spacing is too tight, underlayment is thin, or fasteners are wrong. Schedule service when you see buckling courses, stained soffits, or storms after foot traffic on wet, slippery tiles.

Cracked, buckled, or tight-spaced shake courses

Tight installs leave little room for thermal movement and can buckle tiles or risk manufacturer coverage voids. We check keyway gaps (~3/16 in. minimum; ~3/8 in. preferred for look and movement) and replace damaged units without mixing Spanish barrel profiles into shake layouts.

Leaks at eaves, valleys, or penetrations

In Western Washington rain, ice-and-water at eaves, valleys, and penetrations does the real waterproofing work; synthetic underlayment covers the field. Stains under the eaves usually mean the underlayment path failed—not that “Brava soaked through.” We photo-trace moisture before quoting.

Repair vs. full Brava shake tear-off

Brava shake is not installed over existing shingles—reroofs require tear-off. We use photos to decide isolated tile work vs. deck and underlayment replacement, then write the scope. Call (425) 758-9982 or request a free inspection when appropriate.

Close-up of Brava shake composite tiles on a valley intersection

Weathered gray Brava shake tiles on a residential roof plane

Brava shake roof above a modern patio with outdoor living space

Brava shake tile installation with ridge board staging on site

Brava shake roof on board-and-batten siding home with manicured hedge

Brava shake tile services we provide

Cedar-style Brava shake work scoped for PNW weather and manufacturer layout—not asphalt habits copied onto composite.

Brava shake repair

replace cracked or wind-damaged tiles; fingerprint color-lot matching when lots are available

Keyway spacing correction

open tight courses that buckle or crowd; target ~3/8 in. keyways where the system allows

Tear-off Brava shake reroofs

remove old covering; no overlay over asphalt shingles

Ice-and-water + synthetic underlayment

eaves, valleys, penetrations, and field layers for WA rain; fuller ice/water on lower slopes

Ring-shank / corrosion-resistant fastening

penetrate pad into deck per manufacturer—not smooth-shank asphalt nails

Hip, ridge, and felt interlay details

shake-system ridge vent and interlay pieces—not Spanish barrel parts

Cold-weather install planning

material temperature above 32°F for install; schedule around PNW freeze snaps

Storm docs and inspections

photo reports; see roof inspection before capital decisions

For non-urgent inspections or planned work, see roof inspection & estimate or contact us to schedule at a time that works for you.

Why Brava shake fails when treated like asphalt

Asphalt habits—tight spacing, smooth-shank nails, overlay over shingles—are the most common Brava shake mistakes we see. Correct shake work uses keyway gaps, corrosion-resistant ring-shank fasteners into the deck, tear-off, and shake-only ridge accessories. Curved barrel layouts live on our Spanish Brava S-Tile page.

Composite shake resists the soak that feeds cedar moss and rot, and tiles get slippery when wet—so we plan foot traffic carefully. On qualifying work: 5-year labor / 30-year material warranty; manufacturer material coverage may also apply when install follows their instructions—terms on your estimate.

Brava shake composite roof above a modern patio and outdoor living space

How our Brava shake process works

Photo inspect spacing, underlayment, and deck

We confirm Brava shake (not Spanish barrel), measure keyway gaps, check ice-and-water at eaves/valleys/penetrations, and decide repair vs. tear-off with photos—not driveway guesses.

Written shake scope before tear-off

Estimate lists shake color/lot needs, tear-off, synthetic underlayment and ice-and-water areas, fastener type, ridge/felt details, slope notes, and timeline. You approve before material hits the roof.

Install per shake guidance, then verify drainage

Material staged above 32°F when required; ring-shank fastening into deck; keyway spacing held; wet-tile walking minimized. Cleanup and warranty paperwork on qualifying 5-year labor / 30-year material work.

Warranties on Brava shake tile work

On qualifying Brava shake work we offer a 5-year labor warranty and a 30-year material warranty on eligible products. Manufacturer material coverage may also apply when install follows their instructions—terms on your estimate before you approve.

5

Year labor warranty

30

Year material warranty

FAQ · Contact us for terms on your project.

Warranty: up to 30 years on materials and 5-year labor coverage on qualifying work

Why homeowners choose Construction Elite LLC

Free inspections & written estimates — clear scope before you approve work
Master Craftsman certified crew — repairs to manufacturer standards
Licensed and insured in Washington
Serving Greater Seattle since 2021 — King, Snohomish, and Pierce Counties
Written estimates before permanent repair or replacement begins

Construction Elite LLC leadership on a roofing project

5-Star Rated on Google

Homeowners rate us for keyway-correct Brava shake installs, honest underlayment leak diagnosis, and written scopes—not mixed Spanish barrel parts on shake roofs.

More reviews

Brava shake tile projects

Brava shake fields where keyway spacing, underlayment layers, and ridge details were scoped as a system—not loose “composite shingles” treated like asphalt.

Brava shake composite roof with skylights overlooking landscaped yard

Brava shake roof above a furnished deck in Greater Seattle

Brava shake composite tiles during installation with staging brackets

Brava shake composite tile field during active roof installation

Brava shake tile service area

Based in Bothell—we serve homeowners across King, Snohomish, and Pierce Counties.

Priority cities

Counties

Get started

Common questions

What is Brava shake tile?

Brava shake is a closed-cell composite tile made to look like cedar shake without wood soak, rot, and heavy moss feeding. This page covers shake profiles only—not Spanish barrel tile.

How much spacing do Brava shake tiles need?

Manufacturer guidance calls for roughly 3/16 in. minimum side spacing, with about 3/8 in. keyways preferred for thermal movement and appearance. Crowded installs can buckle and may affect manufacturer coverage when spacing rules are ignored.

Can you overlay Brava shake over existing shingles?

No. Brava shake requires tear-off—overlay over asphalt is not the correct assembly. We scope deck repairs after tear-off when photos show soft spots.

What fasteners should be used on Brava shake?

Corrosion-resistant ring-shank nails or screws—not smooth-shank asphalt nails. Fasteners should penetrate the pad into the deck per manufacturer instructions. Wrong fasteners are a common “treated like asphalt” failure.

Why is ice-and-water so important in Western Washington?

Eaves, valleys, and penetrations see the worst wind-driven rain. Ice-and-water there plus synthetic underlayment in the field is where leak prevention actually happens; lower slopes typically need fuller ice/water coverage.

Can Brava shake be installed in cold weather?

Material temperature should be above 32°F for install. We schedule around freeze snaps and stage product so tiles are workable—not forced when cold and brittle.

Can you match my existing Brava shake color for a repair?

We fingerprint-match and source current color lots when available. Older fields may have faded or discontinued blends—we show you options and put limits in writing on the estimate.

What warranties apply on qualifying Brava shake work?

5-year labor / 30-year material on qualifying work. Manufacturer material coverage may also apply when install follows their instructions—terms on your estimate.

Which areas do you serve?

We dispatch from Bothell across King, Snohomish, and Pierce Counties. See our service areas for priority cities. Call (425) 758-9982.

Related roofing services

Beyond Brava shake work, see emergency roof repair, roof inspection, and residential roof repair across Greater Seattle.

View all services

Local Brava shake

Brava shake by city

City-specific Brava shake scopes across King and Snohomish Counties—cracked composites, valleys, and cedar-style reroofs.

Ready for a Brava shake inspection?

Share photos of cracked or buckled courses, any stains, and roof age. We confirm shake vs. barrel, explain repair vs. tear-off, and send a written quote. Call (425) 758-9982.

Call (425) 758-9982

Request estimate

Construction Elite LLC · 4405 153rd Pl SE, Bothell, WA 98012